Cage position sensor HDS-3series ADS-83series ADS-5series
Feature
This is a photoelectric switch to determine the position of elevator when landing at the bottom.
The switch features a splendid capacity to detect with precision the landing of elevator at the bottom, compared with magnetic sensors. Its main unit is sturdy against vibration and impacts, has a higher protective structure and assembled with materials capable of withstanding severe environmental conditions. It employs a highly reliable electronic circuit, which has been accepted widely in markets.
Specification
You can select from 3 Series of models depending on the type and size of elevator.
HDS-3 Series
This is a U-shaped photoelectric switch for positioning of elevator at the bottom. Its detector can detect up to 3 optical axes.
ADS-83 Series
This is a U-shaped photoelectric switch for positioning. This is best fit to such applications as the detection of elevator position when landing at the bottom, or others. It complies with JIS C8201-5-2 (IEC 60947-5-2).
ADS-5 Series
This is a U-shaped photoelectric switch for positioning of elevator at the bottom. Models for DC 24 V and DC 48 V are available.
Common Specifications
Ambient operating illuminance
|
5,000 lx or less/rapid start fluorescent lamp, 100,000 lx or less/sunlight
(Direct incident light to receiver not allowed in either case.) |
Ambient operating temperature
|
-20 – +55°C, freezing not allowed.
|
Ambient operating humidity
|
85%, dewing not allowed.
|
Vibration resistance
|
Oscillation frequency: 10 – 55 Hz (Sweep for 5 min), amplitude: 1.5 mm for 2 hours each in X/Y/Z direction
|
Shock resistance
|
Acceleration 980 m/s2 (Approx. 10 G), 5 cycles each in X/Y/Z direction
|
Insulation resistance
|
20 MOhm or over, DC 500 V Megger, between bundle of power supply/output cables and case
|
Dieletris resistance
|
AC 1,000 V for 1 min, between bundle of power supply/output cables and case
|
Specifications
HDS-3 Series
Model HDS-3-
|
11
|
21
|
UAX-11
|
UAX-21
|
15
|
25
|
UAX-15
|
UAX-25
|
|
Power supply voltage
|
Rating DC 48 V
Operating rang DC 36 – 60 V Peak voltage 60 V or under |
Rating DC 24 V
Operating range DC 18 – 30 V Peak voltage 30 V or under |
|||||||
Detecting object
|
Opaque object, diameter 10 mm or over
|
||||||||
Control output
|
Non-contact open collector output 1 point/optical axis
Output rating DC 50 mA or under, less than power supply voltage Residual voltage at output “ON” 1.5 V or under, load current 50 mA Leakage current at output “OFF” 0.1 mA or under at rated voltage |
||||||||
Output circuit: PNP type (Source load), common to OUT1 to 3
|
|||||||||
Operation mode
|
Optical axis No. 1 OUT1
|
“ON” at receiving light (Reset)
|
“ON” at receiving light (Reset)
|
“ON” at receiving light
|
“ON” at receiving light (Reset)
|
||||
Optical axis No. 2 OUT2
|
“ON” at light shielded (Detection)
|
“ON” at light shielded (Detection)
|
|||||||
Optical axis No. 3 OUT3
|
|||||||||
Output response time
|
1 ms or less
|
||||||||
Indicator
|
Red LED lights up when detecting object at 1 point/optical axis
|
||||||||
External connection
|
Extension cable : Length (mm)
|
||||||||
5,000
|
2,000
|
5,000
|
2,000
|
5,000
|
2,000
|
5,000
|
2,000
|
||
Enclosure rating
|
IP66
|
ADS-83 Series
Model
|
ADS-83
|
ADS-83-W3
|
|
Power supply voltage
|
Rating
|
DC12/24V
|
|
Operating range
|
DC10~30V
|
||
Detecting object
|
Opaque object, diameter 6 mm or over
|
||
Control output
|
Non-contact open collector output
|
2 points
|
|
Output rating
|
DC 100 mA or under, no higher than power supply voltage
|
||
Residual voltage at output “ON”
|
1.5 V or under, load current – 100 mA
|
||
Leakage current at output “OFF”
|
0.1 mA or under, at rated voltage
|
||
Output circuit
|
NPN type (Sink load)
|
||
Operation mode
|
“OFF” at detecting object (Light shielded)
|
OUT1
|
|
“ON” at detecting object (Light shielded)
|
OUT2
|
||
Output response time
|
1 ms or less
|
||
Indicator
|
Red LED lights up when detecting object
|
||
External connection
|
Connection cable length
|
2,500mm
|
950mm
|
Enclosure rating
|
IP66
|
ADS-5 Series
Model
|
ADS-
|
51
|
52
|
53
|
54
|
55
|
56
|
57
|
58
|
Power supply voltage
|
Rating DC48V
Operating range DC36 – 60V |
◎
|
◎
|
◎
|
◎
|
-
|
-
|
-
|
-
|
Rating DC48V
Operating range DC36 – 60V |
-
|
-
|
-
|
-
|
◎
|
◎
|
◎
|
◎
|
|
Detecting object
|
Opaque object, diameter 6 mm or over
|
||||||||
Control output
|
Non-contact open collector output – 1 points
Output rating DC 50 mA or under, no higher than power supply voltage Residual voltage at output “ON” – 1.5 V or under, load current – 50 mA Leakage current at output “OFF” – 0.1 mV or under, at rated voltage |
||||||||
PNP type (Source load)
|
◎
|
◎
|
-
|
-
|
◎
|
◎
|
-
|
-
|
|
PNP type (Sink load)
|
-
|
-
|
◎
|
◎
|
-
|
-
|
◎
|
◎
|
|
Operation mode
|
“ON” at detecting object
|
◎
|
-
|
◎
|
-
|
◎
|
-
|
◎
|
-
|
“ON” at detecting object
|
-
|
◎
|
-
|
◎
|
-
|
◎
|
-
|
◎
|
|
Output response time
|
2 ms or less
|
||||||||
Indicator
|
Red LED lights up when detecting object
|
||||||||
External connection
|
Extension cable length – 2000mm
|
||||||||
Enclosure rating
|
IP64
|