Products infomation
 
 

CC-Link Remote Communication Products
 

2.CC-Link V1.1-8,16 Bit Support

SOT-CP8/16 Series
 
Feature

Supports CC-Link Ver. 1.10
CC-Link networks give great freedom in building easy-to-use lines. CC-Link's partner product, the space optical transfer system, enables the creation of a system from a large number of distributed I/O devices, reducing costs by reducing the amount of cabling necessary. This is especially useful when communicating with mobile units in an automated conveyance system. The transfer capacity is 8 or 16 inputs and outputs. It can communicate with products in the SOT-CP series, as well as our SOT-NP801/803 space optical transfer system, and our SOT-NP1601/1603 series. A lightweight and compact connector terminal block is used that can be easily connected and removed.

SOT-CP8 series


SOT-CP16 series


Model No. Descriptions




Sample System Configuration




CC-Link Specifications

Applicable PLC
MELSEC A/QnA/Q series, Mitsubishi Electric
Supports A series, QnA series, and Q series
Applicable master unit
AJ61BT11, A1SJ1BT11, AJ61QBT11, A1SJ61QBT11, QJ61BT11
Communication method
Control & Communication Link (CC-Link)
No. of occupied stations
1
Transfer route
Bus
Transfer format
HDLC
Link connect
Connector terminal block (MSTB 2.5/5-ST-5.08, Phoenix Contact)
Connecting cable
CC-Link dedicated cable
Maximum transfer distance
1200 to 100m (depending on baud rate)
Transfer rate
10M, 5M, 2.5M, 625K or 156Kbps

Specifications
8bit Type

Model
SOT-CP801H
SOT-CP801S
SOT-CP803H
SOT-CP803S
Optical axis direction
Head on
Side on
Head on
Side on
Power voltage
DC24V
Operating voltage
DC18 - 30V
Current consumption
100mA MAX
Transfer distance
0 to 1m (with light intensity control knob set to MAX)
0 to 3m (with light intensity control knob set to MAX)
Emitting direction
30 degrees or more (at 1m distance)
5 degrees or more (at 3m distance)
Transfer method
Half duplex
Detection method
Continuous monitoring of bit status changes
Transfer time
15ms max. (in M/S mode) or 20ms max. (in X mode)
Sender element
Near infrared light emitting diode
Receiver element
Photo-transistor
No. of transfer bits
8 points input and 8 points output
No, of control inputs
1 (CTL/TCD)
No, of control outputs
1 (RCV)
Indicator lamp

POW lamp : Lights (red) with power supply on.
CTL/TCD lamp : Lights (red) with CTL input on.
Lights (green) with TCD input on.
DT/RCV lamp : Lights (red) when data is normally received.
Lights (green) when during stabilized reception.
IN lamp : Lights (red) with relevant optical output data on.
OUT lamp : Lights (green) with relevant optical input data on.
RUN lamp : Lights (green) during normal data exchange with master unit.
ERR lamp : Lights (red) with data error received and turns off during normal communication.
SD lamp : Lights (red) during linked data transmission.
RD lamp ; Lights (red) during linked data reception.
Switches
1.Station No. select switches (2 rotary switches)
2.Transfer rate select switch (a rotary switch)
3. Mode select switches (dip switches)
Ambient operating temperature
-20 to 50 deg C (no condensation allowed during operation)
Ambient operating humidity
40 - 85% RH (no condensation allowed)
Ambient operating illuminance
4,000Lx or less (no disturbing rays should directly enter receiver)
Vibration resistance
10 to 55Hz, 1.5mm dual amplitude 2 hours each in X, Y and Z directions
Shock resistance
500m/s2 (approx. 50G), 2 hours each in X, Y and Z directions
Enclosure rating
IP40
Power supply connection
Connector terminal block (MSTB 2.5/2-ST-5.08, Phoenix Contact)
Outside dimensions
90mm (W) 80mm (D) 20mm(H)


16bit Type

Model
SOT-CP1601H
SOT-CP1601S
SOT-CP1603H
SOT-CP1603S
Optical axis direction
Head on
Side on
Head on
Side on
Power voltage
DC24V
Operating voltage
DC18 - 30V
Current consumption
100mA MAX
Transfer distance
0 to 1m (with light intensity control knob set to MAX)
0 to 3m (with light intensity control knob set to MAX)
Emitting direction
30 degrees or more (at 1m distance)
5 degrees or more (at 3m distance)
Transfer method
Half duplex
Detection method
Continuous monitoring of bit status changes
Transfer time
15ms max. (in M/S mode) or 20ms max. (in X mode)
Sender element
Near infrared light emitting diode
Receiver element
Photo-transistor
No. of transfer bits
15 (16) points input and 15 (16) points output
(16th point may be switched to control input/output)
No, of control inputs
1 (CTL/TCD) (with DSW3 off)
No, of control outputs
1 (RCV) (with DSW3 off)
Indicator lamp
POW lamp : Lights (red) with power supply on.
CTL/TCD lamp : Lights (red) with CTL input on.
Lights (green) with TCD input on.
DT/RCV lamp : Lights (red) when data is normally received.
Lights (green) when during stabilized reception.
IN lamp : Lights (red) with relevant optical output data on.
OUT lamp : Lights (green) with relevant optical input data on.
RUN lamp : Lights (green) during normal data exchange with master unit.
ERR lamp : Lights (red) with data error received and turns off during normal communication.
SD lamp : Lights (red) during linked data transmission.
RD lamp ; Lights (red) during linked data reception.
Switches
1. Station No. select switches (2 rotary switches)
2. Transfer rate select switch (a rotary switch)
3. Mode select switches (dip switches)
Ambient operating temperature
-20 to 50 deg C (no condensation allowed during operation)
Ambient operating humidity
40 - 85% RH (no condensation allowed)
Ambient operating illuminance
4,000Lx or less (no disturbing rays should directly enter receiver)
Vibration resistance
10 to 55Hz, 1.5mm dual amplitude 2 hours each in X, Y and Z directions
Shock resistance
500m/s2 (approx. 50G), 2 hours each in X, Y and Z directions
Enclosure rating
IP40
Power supply connection
Connector terminal block (MSTB 2.5/2-ST-5.08, Phoenix Contact)
Outside dimensions
90mm (W) 80mm (D) 20mm(H)

Note: A separate user manual with detailed information about this type is available on request.